QCS-3汽车内饰阻燃试验箱/内饰材料燃烧试验仪
QCS-3 automotive interior materials combustion test device
一、简介
A brief introduction
QCS-3型汽车内饰材料燃烧试验装置，根据国家标准GB8410-2006《汽车内饰材料的燃烧特性》的规定技术要求而设计的，同时符合美国汽车安全技术法规FMVSS 571.302等标准规定的模拟燃烧性能安全试验项目、德标DIN7520《汽车内饰材料的燃烧特性》及TL1010《汽车内饰材料燃烧特性》的相关要求，用于鉴别轿车、多用乘客车、载货汽车和客车内饰材料水平燃烧特性。
QCS-3 type automotive interior material combustion test device, according to national standard GB8410-2006 "combustion characteristics of automotive interior materials" design, and in accordance with the United States automotive safety technology regulations FMVSS 571.302 and other standards for the simulation of safety testing project, German standard DIN7520 "automotive interior materials combustion characteristics" and TL1010 "automotive interior material combustion characteristics" related requirements, for the identification of cars, multi passenger car, truck and passenger car interior material level combustion characteristics.
二、工作条件及主要技术指标
Two, working conditions and the main technical indicators
1.环境温度：-5℃-30 ℃
1 environmental temperature: -5 -30
2.相对湿度：≤ 85%
2 relative humidity: less than 85%
3.供电电压：220V+ 10%、50HZ,功率：100W
3 power supply voltage: 220V+ 10%, 50HZ, power: 100W
4.气源：液化石油气
4 gas source: liquefied petroleum gas
5.秒表精度不低于0.5s
5 stopwatch accuracy is not less than 0.5s
6.本生灯（即燃烧器）对试样施加火焰15s
6 the burner lamp (i.e., burner) is applied to the sample by applying flame 15s
7.本生灯管内径9.5mm+ 0.1mmm，长约100mm
7 the inner diameter of the tube is 0.1mmm 9.5mm+, about 100mm
8.试验倾角：本生灯90°垂直对着水平放置的样品燃烧
8 test angle: the 90 degree of the lamp is burning with the sample placed in the horizontal level.
9.火焰高度：20mm± 2mm 到100mm±2mm可调(一般调为38mm)
9 flame height: 20mm + 2mm + 100mm + 2mm adjustable (generally 38mm)
10.施焰时间：0-999.9s±0.1s可调（一般选择为15s)
10 flame time: 0-999.9s + 0.1s adjustable (general choice for 15s)
11.续燃时间：0-999.9s±0.1s，观察火焰达到*标线后手动开始、手动暂停
11 afterflame time: 0-999.9s + 0.1s, observe the flame to the first line after the manual start, manual pause
12.燃烧气体：液化石油气或煤气
12 combustion gas: liquefied petroleum gas or gas
13.温度范围：0～200℃（显示测试状态下工作室内部温度）
13 temperature range: 0 ~ 200 (show the internal temperature of the studio in the test condition)
三、设备组成
Three, equipment composition
1.设备分控制部分与通风橱一体、燃烧室内置。
1 the equipment control section and a hood, built-in one combustion chamber.
2.点火自动控制系统
2 ignition automatic control system
3.试验过程：试验程序自动控制
3 test procedure: automatic control of test procedure
4.自动进排气系统（燃气自动开启、自动关闭）
4 automatic air intake and exhaust system (gas automatic opening, automatic shutdown)
5.计时系统：燃烧计时器、余焰计时器
5 time system: burning timer, residual flame timer
6.U型支架：上支架有6个销孔，下支架对应有6个销子，并布有线径为0.25mm及间距为25mm的耐热金属支撑线
6.U type bracket, bracket has six pin hole, lower bracket corresponding to have six pin, and cloth cable diameter of 0.25mm and spacing 25mm heat-resistant metal support line
7.试验支架第三标线距第二标线距离为154mm
7 test support third from the second distance 154mm marking marking
8.耐热金属丝槽 0.5mm X 0.5mm 间距 25mm
8 X 0.5mm 0.5mm spacing 25mm
9.金属丝长度大于110mm,每25mm有7~8个光圆齿
9 metal wire length is greater than 110mm, each 7~8 has a 25mm light circle tooth
10.温度数显，测量范围0-200℃
10 temperature display, measuring range of 0-200
11.火焰标尺精度：0.1mm
11 flame scale accuracy: 0.1mm
12.设备外形尺寸：长 * 宽 * 高 1300 * 650 * 1200（钢板静电喷涂材质）
12 equipment appearance size: length * width * high 1300 * 650 * 1200 (steel plate electrostatic spraying material)
四、试样尺寸：长356mm、宽100mm、厚≤ 13mm
Four, sample size: length 356mm, width 100mm, thickness of less than 13mm
五、设计标准
Five, design standards
GB8410-2006
GB8410-2006
FMVSS 571.302等标准规定的模拟燃烧性能安全试验项目
FMVSS 571.302, and other standards for the simulation of the performance of the fire safety test project
DIN7520《汽车内饰材料的燃烧特性》
DIN7520 "combustion characteristics of automotive interior materials"
TL1010汽车内饰材料燃烧特性
TL1010 automotive interior material combustion characteristics
符合标准：GM6090M、DIN75200、GM9070P、FMVSS 302、JIS D 1201、JASO M403 、ISO 3795、ASTM D5132、QB／T 2729-2005
Meet the standards: DIN75200, GM9070P, GM6090M, FMVSS 302, D JIS 1201, M403 JASO, ISO 3795, D5132 ASTM, QB / 2729-2005 T